Ichiro Lubricant Oil Catalogue
Browse a Diverse Range of Lubricant Oil that is optimised for Automotive Performance.
Translate
Use the toolbar below to change your browsing language.
Wide Range of Products that Covers all your Automotive & Industrial Needs
| SAE J300 Viscosity Grades for Engine Oils – December 1999 | |||||
|---|---|---|---|---|---|
| SAE Viscosity Grade | Low Temperature °C Cranking Viscosity(1), Max (CCS) | Low Temperature °C Pumping Viscosity(2), cP Max. with No Yield Stress | Kinematic Viscosity (3)(cSt) at 100°C Min | Kinematic Viscosity (3)(cSt) at 100°C Max | High-Shear Viscosity (4),(cP) at 150°C and 106 s-1Min |
| 0W | 6200 @ -35 | 60000 @ -40 | 3.8 | – | – |
| 5W | 6600 @ -30 | 60000 @ -35 | 3.8 | – | – |
| 10W | 7000 @ -25 | 60000 @ -30 | 4.1 | – | – |
| 15W | 7000 @ -20 | 60000 @ -25 | 5.6 | – | – |
| 20W | 9500 @ -15 | 60000 @ -20 | 5.6 | – | – |
| 25W | 13000 @ -10 | 60000 @ -15 | 9.3 | – | – |
| 20 | – | – | 5.6 | <9.3 | 2.6 |
| 30 | – | – | 9.3 | <12.5 | 2.9 |
| 40 | – | – | 12.5 | <16.3 | 2.9 (0W – 10W) |
| 40 | – | – | 12.5 | <16.3 | 3.7 (15W – 25W) |
| 50 | – | – | 16.3 | <21.9 | 3.7 |
| 60 | – | – | 21.9 | <26.1 | 3.7 |
All values are critical specifications as defined by ASTM D 3244.
cP=1 mPa.s 1 cSt=1 mm2s-1
Notes:
(1) ASTM D 5293.
(2) ASTM D 4684. Note that the presence of any yield stress detectable by this method constitutes a failure regardless of viscosity.
(3) ASTM D 445.
(4) ASTM D 4683, CEC L-36-A-90 (ASTM D 4741), or ASTM D 5481.
| ISO Viscosity Grade Conversions | ||||||
|---|---|---|---|---|---|---|
| ISO Viscosity Grade | Mid-point Kinematic Viscosity | Kinematic Viscosity Limits cSt at 40° (104°F) | ASTM, Saybolt Viscosity Number | Saybolt Viscosity SUS 100°F (37.8°C) | ||
| Min. | Max. | Min. | Max. | |||
| 2 | 2.2 | 1.98 | 2.42 | 32 | 34.0 | 35.5 |
| 3 | 3.2 | 2.88 | 3.52 | 36 | 36.5 | 38.2 |
| 5 | 4.6 | 4.14 | 5.06 | 40 | 39.9 | 42.7 |
| 7 | 6.8 | 6.12 | 7.48 | 50 | 45.7 | 50.3 |
| 10 | 10 | 9.00 | 11.0 | 60 | 55.5 | 62.8 |
| 15 | 15 | 13.5 | 16.5 | 75 | 72 | 83 |
| 22 | 22 | 19.8 | 24.2 | 105 | 96 | 115 |
| 32 | 32 | 28.8 | 35.2 | 150 | 135 | 164 |
| 46 | 46 | 41.4 | 50.6 | 215 | 191 | 234 |
| 68 | 68 | 61.2 | 74.8 | 315 | 280 | 345 |
| 100 | 100 | 90.0 | 110 | 465 | 410 | 500 |
| 150 | 150 | 135 | 165 | 700 | 615 | 750 |
| 220 | 220 | 198 | 242 | 1000 | 900 | 1110 |
| 320 | 320 | 288 | 352 | 1500 | 1310 | 1600 |
| 460 | 460 | 414 | 506 | 2150 | 1880 | 2300 |
| 680 | 680 | 612 | 748 | 3150 | 2800 | 3400 |
| 1000 | 1000 | 900 | 1100 | 4650 | 4100 | 5000 |
| 1500 | 1500 | 1350 | 1650 | 7000 | 6100 | 7500 |
| Viscosity Ranges for AGMS Lubricant Numbers | |||
|---|---|---|---|
| Rust and Oxidation Inhibited Gear Oils | Viscosity Range | Equivalent ISO Gradex | Extreme Pressure Inhibited Gear Oils ISO Grade Gear Lubricants |
| AGMA Lubricant No. | cSt (mm2/s) at 40°C | AGMA Lubricant No | |
| 1 | 41.4 to 50.6 | 46 | |
| 2 | 61.2 to 74.8 | 68 | 2 EP |
| 3 | 90 to 110 | 100 | 3 EP |
| 4 | 135 to 165 | 150 | 4 EP |
| 5 | 198 to 242 | 220 | 5 EP |
| 6 | 288 to 352 | 320 | 6 EP |
| 7 | 414 to 506 | 460 | 7 EP |
| 8 | 612 to 748 | 680 | 8 EP |
| 8A | 900 to 1100 | 1000 | 8A EP |
Notes:
Viscosity ranges for AGMA Lubricant Numbers will henceforth be identical with those of the ASTM system. Oils compounded with 3% to 10% fatty or synthetic fatty oils.
| SAE J306 Automotive Gear Viscosity Classification | Axle and Manual Transmission Lubricant Viscosity Classification | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 70W | 75W | 80W | 85W | 80 | 85 | 90 | 140 | 250 | ||
| Viscosity at 100° | max, mm2/s | 4.1 | 4.1 | 7.0 | 11.0 | 7.0 | 11.0 | 13.5 | 24.0 | 41.0 |
| max,mm2/s | No requirement | 11.0 | 13.5 | 24.0 | 41.0 | No.Req | ||||
| Viscosity of 150,000 mPa.s, max temp °C | -55 | 0-40 | 0-26 | 0-12 | No requirement | |||||
| 20 hr. KRL Shear (CRC L 45-T-93), KV100 after Shear, mm2/s | 4.1 | 4,1 | 7.0 | 11.0 | 7.0 | 11.0 | 13.5 | 24.0 | 41.0 | |
| MIL-PRF-2105E Specification | ||||
|---|---|---|---|---|
| 75W | 80W-90 | 85W-140W | ||
| Viscosity at 100° | max, mm2/s | 4.1 | 13.5 | 24.0 |
| max,mm2/s | – | 24.0 | 41.0 | |
| Viscosity of 150,000 mPa.s, max temp °C | -40.0 | -26.0 | -12.0 | |
| Channel Point, min, °C | -45.0 | -35.0 | -20.0 | |
| Flash Point, min, °C | 150 | 165 | 180 | |
Additive Type : Pour Point Depressant
Purpose : Enable lubricant to flow at low temperatures
Additive Type : Viscosity Modifier
Purpose : Reduce tge rate of viscosity change with temperature
Additive Type : Antifoamant
Purpose : Prevent lubricant from forming a persistent foam
Additive Type : Antioxidant
Purpose : Retard oxidative decomposition
Additive Type : Antiwear and EP Agent
Purpose : Reduce friction and wear and prevent scoring and seizure
Additive Type : Corrision and Rust Inhibitor
Purpose : Prevent corrosion and rusting of metal parts in contact with the lubricant
Additive Type : Detergent
Purpose : Keep surfaces free of deposits
Additive Type : Dispersant
Purpose : Keep insoluble contaiminants dispersed in the lubricant
Additive Type : Friction Modifier
Purpose : Alter coefficient of friction
English 
Chinese